tag:blogger.com,1999:blog-18241657.post5299730627823270962..comments2010-03-12T23:21:16.262-05:00Brian Bohanonnoreply@blogger.comBlogger10125tag:blogger.com,1999:blog-18241657.post-91115805874206699432010-11-17T17:26:01.739-05:002010-11-17T17:26:01.739-05:00Greatissimo! Thanks for the tutorial, now im going to install some Drupal Plugins thereJeebahttp://www.blogger.com/profile/02840151957865072152noreply@blogger.comtag:blogger.com,1999:blog-18241657.post-60068775633003306442010-02-17T20:09:15.623-05:002010-02-17T20:09:15.623-05:00with 9.04/9.10 it&#39;s just one package now<br /><br />https://help.ubuntu.com/community/Nagios3<br /><br />(nagios3)<br /><br />Enjoy.<br />-rpRoger Packhttp://www.blogger.com/profile/01578246846716577925noreply@blogger.comtag:blogger.com,1999:blog-18241657.post-77058412909413960002010-01-07T10:23:27.547-05:002010-01-07T10:23:27.547-05:00Great article!megam.infohttp://megam.info/noreply@blogger.comtag:blogger.com,1999:blog-18241657.post-60699573506596103332009-11-29T08:24:44.199-05:002009-11-29T08:24:44.199-05:00great job! Nagios is up and running ! how about the adds onMiguelhttp://www.blogger.com/profile/00626520747435937713noreply@blogger.comtag:blogger.com,1999:blog-18241657.post-76290369920410015502009-07-21T11:18:19.796-04:002009-07-21T11:18:19.796-04:00A great tutorial...<br />Thank you very much. Francisco -BrazilFrancsico &amp; Fláviahttp://www.blogger.com/profile/17173015486790972755noreply@blogger.comtag:blogger.com,1999:blog-18241657.post-82638863584474377402009-07-21T10:49:20.495-04:002009-07-21T10:49:20.495-04:00Thanks Brian.Shifazhttp://www.blogger.com/profile/09970861945713124553noreply@blogger.comtag:blogger.com,1999:blog-18241657.post-75029340558432160612009-05-29T01:17:07.642-04:002009-05-29T01:17:07.642-04:00Howdy,<br /> This guide was very helpful. I now have nagios up and running. My next step is to go in and configure it.<br /><br /> Can I make a few corrections?<br />1. You refer to a group nagcmd in four places and then call it nagios at the bottom. Change them all to nagios.<br /><br />2. Your lines running ./configure and make(the ones with no parameter) should not be run under sudo. Not only is that bad practice, it is not needed.<br /><br />3. Another dependency is libglib2.0-dev. That is the package name in Ubuntu 9.04 and I suspect 8.10 used the same name<br /><br />4. Near the top, under "Configure Apache to use PHP:", you refer to the file /etc/apache2/apache2.con and it should be /etc/apache2/apache2.conf. You get that file name right later on.<br /><br />5. take the sudo off the two wget commands.<br /><br />6. After your final step, I could get nagios to respond to web requests. But, it had no data and said the service was likely not running. Restarting the machine fixed it. I bet there is a way short of restarting, but I'd mention something about it.<br /><br />Good day,<br />Ralph GreenSirAblehttp://www.blogger.com/profile/16739417964528491480noreply@blogger.comtag:blogger.com,1999:blog-18241657.post-92136357581475972302009-05-25T08:49:09.166-04:002009-05-25T08:49:09.166-04:00Hi,<br /><br />1. I have installed Apache WebServer on Ubuntu server.<br />2. I have installed nagios-3.1.0.<br />3. I am able to view the web-interface successfully in apache server as http://ip address/nagios.<br /><br />4. I have downloaded nagios-php-0.5.1.tar from the net. I would like to configure the PHP web-interface for Negios. What are the configuration steps ? Any help is highly appreciated.<br /><br />Regards,<br />Lalli.selvihttp://www.blogger.com/profile/12410451901317068399noreply@blogger.comtag:blogger.com,1999:blog-18241657.post-47645232569638872722009-05-03T01:18:00.000-04:002009-05-03T01:18:00.000-04:00Thanks for your doc. Pretty nice.<br /><br /> <br /><br />Just to let you know, I'll put small corrections here has I do the procedure.<br /><br /> <br /><br />-This line "# Run in a terminal: sudo vim /etc/apache2/apache2.conf" is actually missing the "f" in "apache2.conf".<br /><br /> <br /><br /> <br /><br />-Just under it, the "DirectoryIndex" actually install himself when you install the libapache2-mod-php5 package in the /etc/apache2/mods-enabled and /etc/apache2/mods-available/dir.conf files.<br /><br /> <br /><br /> <br /><br />-When you edit again the apache.conf file to add the nagios configuration, this is already done with "make install-webconf". Nagios actually install the /etc/apache2/conf.d/nagios.conf file.<br /><br />Have a nice day!Alexandre Racinehttp://www.blogger.com/profile/02524099076726337612noreply@blogger.comtag:blogger.com,1999:blog-18241657.post-89055759879604937002009-04-15T09:58:00.000-04:002009-04-15T09:58:00.000-04:00Why didn't you just use the nagios packages?<br /><br />"sudo apt-get install nagios3"Keithhttp://www.blogger.com/profile/09365320677770571158noreply@blogger.com